MOTOROLA VIP2262 CODE
MOTOROLA VIP2262 TV
MOTOROLA VIP2262 WINDOWS

if the suffix is 0 for the first key (4) pressed, it will be 1 for the second key (2). I believe that the VIP2262 uses debounce with an alternating suffix that is shared for the complete remote. Only some digits gets through (and some digits only get through sometimes). However, even when all commands are programmed this way, Win7 cannot control the STB accurately. Win7 goes into a never ending loop asking for the same key to be pressed unless you point at Win7 then point the remote away and press another key and then point at Win7 again. What I believe is needed is to alter how Win7 sends IR signals to the STB.ДЄrya S Asok, I get stuck on step l (L). However, I believe that the suggested registry setting only affect how Win7 interprets IR signals sent to it. S.Sengupta was on the right track with that is has to do with debounce processing. Win7 media center, HVR-2250 but a Motorola VIP2262. I have a very similar setup as the original question.

MOTOROLA VIP2262 WINDOWS

I would also suggest you to perform windows updates.

MOTOROLA VIP2262 TV

Select 'Return to TV Settings' and click 'Finish' Select 'The channel changed correctly' if it changed and then 'Next'. It does go in order (1, 2, 3, 4.), so if the channel does notД®xist, just hit up or down until it hits a channel that exists. With a delay, the channels should change. Q) On the Set IR Signal Speed screen, hit the channel up or down buttons at least six times. If successful, select 'The set-top box changed the channel correctly', then 'Next'. Wait about 10 seconds and the channel should change (Give it a little time for the IR signal to travelДown the wire to the Set-top Receiver and the TV signal to clear the video capture card buffer to the screen). P) On the Test Channel Changing Screen, use the Media Center Remote and try changing the channel. O) On the How Do You Change Channels? Screen, Select the appropriate option and click 'Next'. N) On the Select Number of Digits Screen, select the appropriate amount and then 'Next. M) On the Set-top Box Codes Learned Successfully Screen, click on 'Next'. Line of site on the receiver until the button is held down for a second and that when held up to the receiver, it is no more than three inches from it. If it takes more than 4 times (one entry try and one confirm try), then make sure the remote is not in the L) Do this a minimum of two times until it is ready for the next button and repeat step 10. Hold down the number, raise the remote to the receiver until it says 'Release button to continue' then move it away from the IR K) On the IR Learning Screen, Hold the remote away from the IR receiver. J) On Channel Change Buttons, select the method used. I) On the Prepare to Identify Remote Screen, hit next. Select 'Have Media Center learn my remote from scratch' and then 'Next'. G) On the Identify Set-top Box Remote, click 'Next'. To learn the controls for the STB, go through the TV Signal setup again and follow these steps:ДЄ) On the Automatic TV Signal Setup Screen, select 'I will manually configure my TV signal' and click 'Next'.Д«) On the Select Your TV Signal Screen, select 'Cable' and then Next.Д¬) On the Do You Have a Set-top Box Screen, click 'Yes' then next.Д) On the Prepare for Set-top Box Setup screen, click 'Next'.Д®) On the Select a Working TV Signal, Select the one you haveДЇ) On the Set-top Box Remote Screen, Select ''Yes' and then 'Next'. Jobs' promise of 'it just works' is increasingly compelling given all the BS i've put up with over the years dealing with crappy microsoft products that go by the mantra of 'it sometimes works'. The dozens of ppl that rely on me for tech advice. if an appropriate solution cannot be identified, i might have to jump to the Apple bandwagon, and recommend the same to My logitech universal remote was able to work as soon as i told the setup what set-top box i had. I majored in EE/CS, and have worked for 11 years in the tech industry, including 4 years designing consumer electronics silicon, so i don't believe i'm not following the directions correctly (re: not user error). this did not work either (although it did say it 'learned' successfully, but then does not have any effect when attempting to change channels). Vision for both the automatic and IR learning setup. i've also tried the trick of holding down the remote button hidden from the IR sensor, and moving it into and out of the sensor's

MOTOROLA VIP2262 CODE

(automatic, remote control code selection, and IR learning). I've tried every method of configuring the IR blaster, but NONE work. i have the IR blaster positioned correctly in front of the STB. trying to setup live tv with u-verse, using a motorola VIP-1200 set top box. I'm running win7, with a hauppauge winTV-HVR-2250.

Motorola vip2262